
ServicesWindow Retrofitting
Window Retrofitting in Irvine
We take out the old sashes and glass, leave the original frame in the wall, and set a new window into it. A flush fin covers the old edge, so your stucco stays put. Less mess, less patching, and a typical house is done in a day or two.
What a Retrofit Is and When It Makes Sense
A retrofit is a way to get new windows without cutting into the outside wall. Most stucco homes in Orange County were built with aluminum windows nailed in before the stucco went on. Pulling those frames out means breaking stucco, patching it and repainting. A retrofit skips that. We strip the old window down to its frame, then fit a new custom-sized unit inside it.
The new frame is the part you choose. Vinyl is the most common pick. It insulates well, never needs paint and handles our dry summers fine. Fiberglass costs more, but it barely expands in heat, so it holds its shape on sunny south and west walls and can be made in darker colors without warping. Some people want a narrow aluminum look; we can talk through how that trades off against heat and condensation.
Retrofit is the right call when the old frame is solid and square. If we find rot, water damage at the sill or a frame that has shifted, we will tell you, and full-frame window replacement is the better job for that opening.
What the Work Includes
Measuring every opening
Each window is built to order, so we measure each frame in three spots, top to bottom and side to side. Old houses settle, and a window that is off by a quarter inch will not seal right.
Removing the old sash and track
We pull the glass panels, the tracks and any loose hardware. The frame stays in the wall. We clean out old caulk and dirt so the new window sits on a clean surface.
Checking the frame
Before anything new goes in, we look at the sill and corners for rot, rust or cracks. You will see what we find before we move ahead.
Setting the new window
The new unit goes in level and plumb, shimmed where needed and fastened through the frame. A flush fin, sometimes called a Z-bar, laps over the old frame on the outside.
Sealing inside and out
We run sealant around the outside to keep water and dust out, and finish the inside edge with caulk or trim so it looks clean. Then we test every lock and slider.
Cleanup and haul-off
Old glass and aluminum leave with us. We vacuum the sills and wipe down the floors near each opening.
Signs Your Windows Are Ready for a Retrofit
Single-pane aluminum sliders
These are original in a lot of homes here. They pass heat straight through in summer and feel cold to the touch on winter mornings.
Sweating glass and black tracks
Condensation on the inside of aluminum frames runs into the track and leaves mildew. It comes back no matter how often you clean it.
Sliders that stick or jump the track
Worn rollers and bent tracks make windows hard to open. When the rollers are no longer made, a new window is often the only real fix.
Fog between the panes
On dual-pane glass, a cloudy haze means the seal has failed and the gas fill is gone.
Drafts and street noise
If you hear traffic clearly or feel air moving near a closed window, the seals and weatherstripping are done.
How the Job Runs
- 1
Estimate at your home
We come out, look at each window, measure and walk you through the material options. You get a written price for each opening. There is no pressure to sign anything that day.
- 2
Ordering
Once you pick your frame material, color and glass, we order the windows to your sizes. Custom units usually take a few weeks to arrive, and we call you to set an install date.
- 3
Install day
Floors and furniture near each window get covered before we start. We finish one window completely, old unit out and new one sealed in, before touching the next, so only one opening in your home is ever open at a time.
- 4
Walkthrough
We open, close and lock every window with you. We show you how the screens and any tilt-in sashes work, and point out anything we found along the way.
What Moves the Price
Every retrofit is priced per window, and each window is a little different. These are the things that make the biggest change. We go over each one with you at the estimate so the number makes sense.
- Size and window style
- A small bathroom slider and a large picture window are very different jobs. Casements and single-hung units cost more to build than basic sliders.
- Frame material
- Vinyl is the most budget-friendly. Fiberglass and darker exterior colors add cost but hold up better in direct sun.
- Glass package
- Low-E coatings, laminated glass for noise and security, and obscure glass for bathrooms each change the price. State energy rules also set a minimum glass rating.
- Frame condition
- If a frame needs repair or an opening turns out to need full-frame work, that changes the scope. We tell you before we do it.
- Height and access
- Second-story windows over a slope or roof need more setup and sometimes extra hands.
Window Retrofitting Questions
Something not covered here? (949) 638-3312
Is a retrofit as good as a full-frame replacement?
When the old frame is sound, yes. The new window seals to that frame, and the flush fin sheds water over it. Where it falls short is when the frame itself is damaged, because a retrofit does not fix what is behind it. That is why we check each frame first.
Will I lose any glass area?
A little. The new frame sits inside the old one, so the visible glass shrinks slightly on each side. Most people do not notice once it is in. Slim-frame vinyl and fiberglass lines keep that loss small, and we can show you samples.
Will my stucco or drywall get damaged?
That is the main reason people pick a retrofit. The old frame stays in the wall, so the stucco outside and the drywall inside are left alone. You may see some old caulk lines we clean up, but no patching or painting.
Does my HOA need to approve new windows?
Many Irvine neighborhoods have HOA rules about frame color and grid patterns. Check with yours before you order. We can give you the product details and color names your HOA usually asks for.
Do I need a permit for a retrofit?
Window changes in California often require a permit so the city can confirm the glass meets energy code. We handle the permit when one is required and schedule any inspection.
Can I do some windows as retrofits and some as full-frame?
Yes. It is common to retrofit most of the house and do full-frame work on one or two openings with damage. We price each one separately so you can see the difference.

See Which Frames Fit Your Home
We bring frame and glass samples to your home, check every opening and give you a written price. Free in-home estimates with no sales pressure or obligation.